Send the address and what you see. We reply with the rule that applies in Redondo Beach and a written price range.
Ask a building inspector about Redondo Beach and you will hear about beach cottages, postwar homes in north redondo, and newer townhomes with factory-built gas fireplaces. Each of those brings its own clearance, liner and permit questions, and Meadowbrook Chimney Care answers them in writing on every chimney rebuilds visit in Redondo Beach, CA.
City served
Redondo Beach, CA
ZIP codes on route
2
Next door
Manhattan Beach and Torrance
Typical housing
beach cottages, postwar homes in North Redondo, and newer townhomes with factory-built gas fireplaces
Marine air near the harbor rusts dampers, caps and chase covers within a few years, so we fit only stainless or copper here. Crowns and mortar close to the water also stay damp for days after a winter storm.
Route and permits
Some streets sit near a city line, and the line decides the permit office. Find your neighborhood below, or call and we confirm it from the address.
Many Redondo Beach townhomes and condos have factory-built fireplaces, which follow the manufacturer's listing rather than the masonry code. Parts borrowed from another brand, or an insert the listing does not permit, are the problems we find most in those units. We see single-flue brick, shared multi-flue stacks and factory-built chases in this area, and each gets inspected to its own rulebook.
Housing here includes beach cottages, postwar homes in north redondo, and newer townhomes with factory-built gas fireplaces. Those differences change liner sizing, cap fit, permit needs and how much of the chimney can be reached without opening a wall.
Redondo Beach is on our direct route, with nearby stops in Manhattan Beach and Torrance. ZIPs 90277 and 90278 fall within standard coverage. Phone or use the form and a written confirmation follows.
An inspection often turns up a second job. These are the ones that tend to follow, each with its own written scope.
Flue brushing and vacuuming to the NFPA 211 cleaning rule, with the cap, damper and crown looked over and a dated note left behind.
See this scopeMatched to one of the three NFPA 211 levels, chosen from what has happened to your chimney since it was last examined.
See this scopeWater entry and quake cracks fixed at the cause, so the chimney meets the standard again rather than just looking patched.
See this scopeHearth size, trim distance and firebox condition measured against the building code or, for prefab units, the maker's listing.
See this scopeFirebrick, panels, dampers and smoke chambers repaired with refractory materials or the maker's own parts, never generic swaps.
See this scopeRequired by NFPA 211 at a sale, a fuel change, a relining or after a quake or chimney fire, with a full-height video scan.
See this scopeSpark-screened stainless caps sized to the code: half-inch maximum openings and open area four times the flue outlet.
See this scopeTwo-layer step and counter metal rebuilt at the roofline, with a cricket added where a wide stack requires one.
See this scopeRepointing with mortar softer than the brick, spalled units replaced, crowns rebuilt to shed water clear of the face.
See this scopeSoot and ash cleared from firebox, doors and hearth so the walls, panels and joints underneath can actually be judged.
See this scopeAnnual service the way the unit's own manual describes it, from burner ports and pilot to log placement and the outside vent.
See this scopeDiagnosis by meter of pilots, thermopiles, valves and ignition, fixed with listed parts and leak-tested before we leave.
See this scopeMantels, surrounds and hearths designed inside the clearance limits from the start, with any permit path written into the plan.
See this scopeLiner sized and connected as the listing requires, Level 2 done first, gas line permitted, and clearances measured before ordering.
See this scopeError codes read and each step of the feed and burn cycle tested, with safety switches kept working, never bypassed.
See this scopeDoor gaskets, baffles, firebrick and combustors swapped with model parts, and the label clearances to walls and floor measured.
See this scopeVented or vent-free sets chosen by what the city allows and the firebox can take, with a damper clamp on every vented install.
See this scopeThe same scope applies next door, but the permit office and house types change. Pick a city to see its notes.
the flat, mostly postwar streets at the middle of the South Bay
Most Torrance fireplaces went in during the postwar building boom, before the code asked for steel reinforcement in chimneys. A cracked crown or a leaning stack here is more than a cosmetic item, because any rebuild has to meet today's seismic rules. Permits for inserts and rebuilds go through the city's building department, and we write those steps into the scope.
Read the city notesthe port city's older neighborhoods, from Bixby Knolls to Belmont Heights
Long Beach holds a large stock of 1920s homes, and the 1933 Long Beach earthquake is one reason California began writing seismic rules for buildings. Many chimneys from that era are unreinforced, and some were rebuilt in a hurry decades ago, so an inspection here often has to sort out which parts meet any standard at all.
Read the city notesthe peninsula hills where fire zone maps and landslide ground shape what gets built
Much of Rancho Palos Verdes is mapped as a Very High Fire Hazard Severity Zone, which puts the spark arrestor on every wood-burning chimney under close watch from fire officials and insurers. In and near the Portuguese Bend landslide area, ground movement can crack a chimney from below, so a Level 2 camera scan is often the honest place to start.
Read the city notesthe horse-property lanes on the inland slope of the peninsula
Big ranch-style houses here often carry wide, heavy chimneys built before crickets and seismic reinforcement were standard. A wide stack without a cricket tends to leak on its uphill side, and rebuilding one means adding the steel the current code asks for.
Read the city notesYes, every week, along with Manhattan Beach and Torrance. Each visit ends with written notes that cite the rule behind any finding.
Usually taken down to sound masonry, 3-2-10 height rule met, vertical steel and horizontal ties. The exact list follows the type of fireplace, its listing or the code that governs it, and what the chimney shows on the day.
Often. A sale, an insurer's request, a new appliance or a quake are all common triggers in ZIPs 90277, 90278, and a dated record from a licensed company answers each of them.
